利用随机试验法等数值计算方法求得了模型中的表观活化能和视频率因子等动力学参数。
The kinetic parameters in the models, including pseudo activation energy and apparent frequency factor were obtained by using Monte Carlo numerical calculation method.
目的构建有效的膝关节三维模型以计算髌股关节动力学参数。
Objective the three-dimensional knee model has been developed to compute the kinetics of patella-femoral joint.
将高速滑体制成相似的机翼模型，进行风洞试验，即可测定滑坡凌空飞行的空气动力学参数，从而计算大型高速滑坡凌空飞行的空气动力升力、飞行速度和飞行距离等。
If we make a wing model which is similar to sliding mass, we can determine aerodynamic parameters by the wind tunnel testing and thus calculate the lift.
目的：建立一种根据血药浓度的微分特征计算静脉滴注双室模型药物动力学参数的新方法。
AIM: To establish a new method for calculating the pharmacokinetic parameters of bi-compartmental drugs based on the plasma level of the drug during the intravenous infusion phase.
因此，为了分析不同线路设计参数对舒适度的影响，应采用车—线耦合动力学模型进行计算仿真。
So in order to analysis the impact of different alignment on the comfort index, we should establish a dynamic model to make a car-guideway coupling emulation.
同时以软化点为参数建立老化动力学模型来反映两种沥青的老化情况，并计算出活化能。
Based on parameter of softening point, aging kinetics model was established to show aging condition of two asphalts and to calculate activation energies.
由此可见，裂纹的定量辩识对动力学计算模型和裂纹参数搜索两方面的效率要求非常高，关系到其在工程实际中是否具有应用价值。
It can be seen that the efficiency of the dynamic model and the searching of crack parameters is crucial to the practical application of the quantitative crack identification techniques.
基于改进的单纯形算法和残数法，对药物动力学房室模型中的有关参数计算进行了研究。
By using improved simplex method and residuals method, a calculation based on the parameters of compartment model of pharmacokinetics is presented.
结果得到血管内给药二室模型药代动力学参数估算的电子计算机程序。
Results An electronic computer program for pharmacokenetic parameter estimation was gained, and was applied to the pharmacokenetic parameter estimation.
通过对干c DQ电磁振动给料机主振动系统的受力分析，建立振动力学模型，并进行动力学参数计算。
Through the force analysis of the main vibration system about the CDQ electromagnetic vibration feeder, the vibration mechanical model is established and the dynamics parameter is computed.
该文导出了核酸探针在石英晶体微天平电极表面上的杂交反应动力学模型，并通过实验对导出模型进行了验证、计算出相关动力学参数。
The dynamic model of nucleic hybridizing reaction on the surface of the electrode of quartz crystal microbalance(QCM) was deduced, and it was well validated.
通过对机构模型进行分析计算可求解膝关节的运动及动力学参数。
Kinematics and kinetics of knee can be calculated from the mechanical model.
基于上述试验研究，本文采用双组份分阶段一级反应动力学模型，分别计算了在空气和氮气两种气氛下固体可燃物的表观动力学参数。
Based on the previous TGA studies, double components multi-step first order reaction kinetic model was used to describe the process of pyrolysis of wood.
PCNONLIN程序进行药物动力学房室模型数据拟合和参数计算；
The modelling data were performed with a compartment pharmacokinetic modelling program (PCNONLIN).
通过实验测出动力学参数后，设计编制了模型的计算软件。
This kinetic. model is based on the structual group composition of feedstock, and a software of the model was developed according to the experimental kinetic parameters.
动力学节点计算机生成兵力（CGF）系统中建立了实体的气动全量模型及极限参数模型，采用AI技术进行战术决策。
The aerodynamic model and the limited parameter model are all realized for airplane entity in CGF system at the dynamic nodes, and the AI technology is applied for the tactic decision.
通过示差扫描量热实验计算出模型中固化动力学参数。
The kinetic parameters of polymer matrix used for simulation were acquired from the differential scanning calorimeter scans.
通过示差扫描量热实验计算出模型中固化动力学参数。
The kinetic parameters of polymer matrix used for simulation were acquired from the differential scanning calorimeter scans.
应用推荐