在纤维端部存在高切变应力视为导致产生裂缝的因素。
The occurrence of high shear stress at the fibre end is a factor which is expected to lead to crack generation .
这些结果表明，动脉粥样硬化早期病变受低切变应力的影响。
All the above showed that early atherosclerosis changes were affected by low-shear stress.
根据图标上的切变应力，设计中采取更集中的结构尽量减少整个钢结构的分段。
Trying to minimize the amount of different steel sections, we design a pattern that becomes denser according to the diagram of shear stress.
目的探讨切变应力对猪髋动脉内皮细胞单独培养和猪髋动脉内皮细胞与猪小肠黏膜下基质联合培养形态学特征的影响。
Objective To investigate the morphological effect of fluid shear stress on pig iliac endothelium cells cultured solely or co-cultured with pig small intestinal submucosa.
随着粘贴层的切变模量的增加或其厚度的减小，切应力在靠近压电致动器端部区域迅速增大。
The shear stress sharply rises at the ends of the piezoelectric as the shear modulus increasing or the thickness decreasing.
剪切变形的影响使得箱形梁的翼板中出现应力不均匀现象，尤其是悬臂箱形梁剪力滞现象。
The influence of shearing deformation causes the non-uniform stress in the wing plate of the box girder, especially the cantilever box girder.
比较了考虑横向剪切变形的几种力学模型，提出了一种新的假定剪应力沿板厚呈抛物线分布的分层模型。
This paper compared several mechanical models with transverse shear deformation and put forward a kind of layer model assuming that shear stresses vary parabolically through the plate thickness.
结果表明：四边铰支的正交异性层合板，当其长厚比小于30时，横向剪切变形对其位移和应力的影响是不容忽略的。
The results showed that the effects of traverse shear on displacement and strees are not ignorable, as the length thick ratio of laminate is less than 30.
应力-应变图可以用来表现剪切应力与剪切变形。
A stress-strain diagram can be plotted using shear stress and shear strain.
剪切应力，是成矿的主要动力来源，各剪切变形阶段，均有矿液的迁移、叠加和富集。
The shear stress is the main power source for mineralization, and activation, overlapping and enrichment of ore-forming fluid occur in each shear deformation phase.
在所研究的剪切应力、剪切速率及温度范围内，两者均属于假塑性流体，呈现剪切变稀行为。
The results show that HDPE/MMT nano-composite and HDPE belong to pseudoplastic fluid and present, shear thinning behaviors within the range of shear stress, shear rate and temperature.
最后，对新本构关系与其它理论的本构关系作了比较，计算了简单剪切变形的应力。
Finally, the stresses of simple shear deformation are worked out to examine some constitutive relations.
密度是决定初始弹性模量的根本因素，而剪切变形过程中弹性模量则是密度和应力状态共同决定的。
Density is the essential factor to decide the initial elastic modulus, and the elastic modulus in shear process is the result of combined action of stress status and density.
表观粘度对切变速率和切应力较敏感，并且，在低切变速率下对温度也较敏感。
It has been found that the apparent viscosity of PBR is sensitive to shear rate, shear stress, and to temperature at lower shear rate levels as well.
发现钛合金铆钉在应力波铆接过程中，主要是以绝热剪切变形的方式实现冷加工塑性变形的。
It is shown that the cold-worked plastic deformation of TB-2 in the process of stress-wave-riveting is achieved in the form of adiabatic shear substantially.
岩土体应力状态靠近极限状态线时，岩土体塑性剪切变形越来越大，趋于破坏；
The plastic deviatoric deformation becomes larger and larger and geomaterials tend towards to damage, when the stress state of geomaterials is close to the critical state line.
岩土体应力状态靠近极限状态线时，岩土体塑性剪切变形越来越大，趋于破坏；
The plastic deviatoric deformation becomes larger and larger and geomaterials tend towards to damage, when the stress state of geomaterials is close to the critical state line.
应用推荐