适合不同切削深度和间断性切割。
适合变化的切削深度和适合间断性切割。
在干切状态下，切削深度对刀具寿命影响最大。
Under dry cutting state, tool life is affected mostly by cutting depth.
适合锐角的切削角度、切断操作和变切削深度。
For positive chip angles, interrupted cutting and varying-cutting depth.
切削深度d是未加工面与已加工面之间的垂直距离。
Depth of cut, d, is the normal distance between the unmachined surface and the machined surface.
对优控主轴转速系统的极限切削深度进行了试验考证。
The limit cutting depth of the machining system with optimal controlling spindle speed is studied by experiments.
Mistracking主导产品滑动和切削深度不足。
Mistracking led to product sliding and insufficient cutting depth.
还可以看到当刀具进入工件切削时直接达到最大切削深度。
It can also be seen that the maximum depth of cut is achieved directly as the cutter engages with the workpiece.
为探讨微切削的加工机理，对能稳定切削的最小切削深度进行了研究。
To probe into machining mechanism in micro cutting, the minimum cutting depth for achieving stable machining was discussed.
工件被夹持到位，铣刀靠着提供安装或铣刀位置及切削深度的安装台定位。
The workpiece is clamped in position, and cutter is located against the setting block, which provides setting or cutter position and depth of cut.
老式机床通常是由工人操作并由他们决定机床速度、进给量、切削深度等。
Early machine tools were operated by craftsmen who decided many variables such as speeds, feeds, and depth of cut, etc.
研究用自旋转车刀加工金属纤维时，切削深度和进给量对纤维力学性能的影响。
The effects of the machining depth and the amount of feed on the mechanical properties of the metal fiber to be machined with the self propelled rotary turning tool are researched.
冲击切削与静压切削相比，不仅可以增大切削深度，而且可以大量降低切削力。
Impact cutting and cutting compared, not only can increase depth of cut, but can also reduce the large number of cutting force.
研究了用自旋转车刀加工金属纤维时，切削深度和进给量对纤维力学性能的影响。
In this paper, effects of depth of cut and feedrate on mechanical properties of metallic fiber are investigated by spinning bit.
改善表面粗糙度应重点从进给量考虑和切削深度考虑，切削速度的影响是比较小；
To improve surface roughness should be considered from VF and cutting depth while the cutting speed is of a little use.
轴向进给通过大拖板或复式刀架手动或自动提供，然而切削深度则由横向滑板控制。
The axial feed is provided by the carriage or the compound rest, either manually or automatically, whereas the depth of cut is controlled by the cross slide.
有可能对切削深度产生误判，以至于割得如此之深，需要缝合(或者在极端情况下需要住院)。
It's possible to misjudge the depth of a cut, making it so deep that it requires stitches (or, in extreme cases, hospitalization).
在端面车削操作中，进给由横向滑板提供，而切削深度则通过大拖板或复式刀架控制。
During a facing operation, feed is provided by the cross slide, whereas the depth of cut is controlled by the carriage or compound rest.
合适进给的选择取决于许多因素，例如所需表面光洁度、切削深度和所用刀具的几何形状。
The selection of a suitable feed depends upon many factors, such as the required surface finish, the depth of cut, and the geometry of the tool used.
粗车中，推荐使用较大切削深度(根据工件材料可达0.25英寸或6毫米)和较小进给。
In roughing cuts, it is recommended that large depths of cuts (up to 0.25in. or 6mm, depending upon the workpiece material) and smaller feeds would be used.
因卡爪硬度较高，又系断续切削，所以修正时切削深度和走刀量要小，切削速度也不宜太高。
The clamping claw with high hardness, and intermittent cutting, so that when the cutting depth and cutting amount is small, the cutting speed is not too high.
在本试验参数范围内选取切削参数时，切削速度、进给量取中值有利，切削深度取小值有利。
At the range of the testing parameters it is of advantage to select middle value of feedrate and cutting speed, and smaller value of cutting depth.
通过车铣和车削两种加工方法的对比，重点研究了切削深度对微细轴类零件加工精度的影响问题。
Contrast the two machining method between turn-milling and turning, research the effect on machining precision of micro-shaft parts about cutting depth.
以单因素实验法分别考察了刀具材料、冷却条件、切削深度、进给速度等对刀具磨损的影响规律。
In single factor test, the influencing factor of tools wear was discussed, such as tool material, cooling conditions, cutting depth and feed speed.
通过试验，找出了切削深度、切削速度、每齿进给量等切削用量及切出角影响面铣刀寿命的规律。
Tests are conducted to find the rules how such cutting parameters as cutting depth, cutting speed and feedrate per blade as well as the cutting angle affect on the life of face mill.
结果表明：工件进给速度对表面粗糙度的影响最大，切削深度和刀具前角次之，工件硬度影响最小。
The results show that the effects on surface roughness are feed speed, depth of cutting , tool rake angle and parts hardness in turn.
就像在此图中能看到的那样，切削深度(及作为结果的载荷)随着切削刃持续进入切削而逐渐增加。
As we can see in that figure, the depth of cut (and consequently the load) gradually increases on the successively engaged cutting edges.
就像在此图中能看到的那样，切削深度(及作为结果的载荷)随着切削刃持续进入切削而逐渐增加。
As we can see in that figure, the depth of cut (and consequently the load) gradually increases on the successively engaged cutting edges.
应用推荐