突出于滚道表面与滚动方向平行的窄凸肩。
Prominent in the raceway surface and rolling direction parallel to the narrow shroud.
在内部作成圆形凸肩以代替锐缘孔板状的侧面。
It has rounded shoulders inside instead of the sharp orifice - like edge.
在内部作成圆形凸肩以代替锐缘孔板状的侧面。
It has rounded shoulders inside instead of the sharp orifice-like edge.
此外，突出的凸肩(17)用于支撑一绝缘子装置(15)。
Furthermore, the projecting shoulder (17) is used for supporting an insulator arrangement (15).
最后，按照设计的实验方案，对带凸肩叶片组试件做了振动实验研究。
Dimensionless dry friction damping factor is defined to measure the effect of dry friction damping, Finally, according to designed method, a vibration experiment of shrouded blades is carried out.
本文对卡箍式结构中简体凸肩结构通过不同结构方案的分析计算给出了优化设计。
The optimization design of the shoulder structure of the cylinder by analyzing and calculating different structures about the split - clamp equipmen was outlined.
她的第二个全套衣服是一个锐的凸肩，白色T恤分层在动物印花皮质宽松瘦慢跑裤。
Her second ensemble is a sharp shouldered white T-shirt layered over animal-print skinny joggers.
获得了凸肩接触面初始正压力、接触角度、接触刚度、摩擦系数等多种参数对叶片非线性响应的影响规律。
The influences of many contact parameters such as initial normal force, contact angle, contact stiffness and coefficient of friction were obtained.
基于压杆稳定理论，探讨了该制件镦压凸肩的工艺条件，计算所需的工艺力，介绍其镦压成形模具的设计结构、工作原理。
Process condition of upsetting shoulder was discussed and forming force was calculated based on column buckling theory. The die structure and working principle was introduced.
输送管（1）具有一 个双层的管身（2），该管身在入口侧的管端（5）上并且在出口侧的管端（6）上分别设置一个联接凸肩（7、8）。
The delivery pipe (1) has a double-layer pipe body (2) which has in each case a coupling collar (7, 8) at the inlet-side pipe end (5) and at the outlet-side pipe end (6).
由于带阻尼围带或凸肩叶片(以下简称阻尼叶片)的运动方程中的阻尼矩阵是非解耦的矩阵，只有引入复模态理论才能圆满解决其特征问题的求解。
Since the damping matrix in the motion equation of damped blade is no longer decoupled as Rayleigh damping, so the complex mode theory is introduced in this paper to overcome the difficulty.
于上架梁的下方固定有顶杆和凹模，于下架梁上安装有其一端部至少有一个肩凸的型芯。
An ejector rod and a female die are fixed at the lower part of the upper beam, and a mold core is mounted on the lower beam. The end of the mold core has at least one shoulder.
于上架梁的下方固定有顶杆和凹模，于下架梁上安装有其一端部至少有一个肩凸的型芯。
An ejector rod and a female die are fixed at the lower part of the upper beam, and a mold core is mounted on the lower beam. The end of the mold core has at least one shoulder.
应用推荐