它们在火山喷发口凝聚、冷却、沉淀。
They melted in the volcanic orifice, agglomerated, cooled and sank out.
这些冷却空气通过两根垂直管道进入到机柜的顶部，然后在分流进入那些空气杆，这些空气杆是有序的排列着冷气释放口的长长的薄薄的管道。
The chilled air enters the top of a rack through two vertical standpipes, which branch off into air wands -long, thin pipes lined with vents that release cold air.
出料口有超强冷却系统，保证粘合效果；
有时，较低的口模温度会在口模内表面上生成一个冷却的树脂层，这个树脂层慢慢地移出到口模出口，然后与本体料流分离，从而引起积料。
Sometimes lower die temperatures can create a cool layer of resin on the inner surface of the die that creeps slowly to the die exit and then separates from the bulk flow, causing buildup.
通过吸附作用、压缩作用或冷却作用，从套管头气回收到的液态烃，为一种汽油。套管头气是从地面上的一口油井所采到的气体。
The liquid hydrocarbon recovered from casing head gas by adsorption, compression, or refrigeration. Casing head gas is the gas recovered at the surface from an oil well.
不希望再次出现这种情况，许多操作者就把喂料口的冷却水打满。
Not wanting that to ever happen again, most operators run full coolant flow to the feed throat.
目的：观察潜艇艇员冷却背心装填物凝胶经口急性毒性。
Objective: to observe acute peroral toxicity of gelatum in the cooling vest for the submarine crew.
真空室顶部预留了法兰口并配有冷却靶台。
There are water cooling target chuck and back flanges on the top of the vacuum chamber.
研究湍流管式冷却器的冷却机理和设计问题，讨论了湍流管入口角、出口角、喉口直径和水缝的选择范围。
The choosing range of the input Angle and output Angle of turbulent tube, the diameter of the throat mouth and water gap are discussed.
该流体冷却器专门设计用于去除塑料和工业进程的废气热量，这些过程包括液压系统、供料口、模具和材料。
The hydra Hybrid Fluid Cooler is designed to remove waste heat from plastics and industrial processes, including hydraulics, feed throats, molds and material.
采用冷却-凝固状态图可以预测铸铁是按白口、灰口或麻口凝固。
The cooling-solidification diagram can be used to forecast whether the cast iron will solidify in accordance with the white iron style, gray iron style or mottled iron style.
对牛口峪水库石化污水回用于循环冷却水进行了动态模拟试验研究，确定了试验方案和工艺条件。
Dynamic simulated tests are made for petrochemical sewage in Niukouyu Reservoir reused for circulating cooling water system.
研究湍流管式冷却器的冷却机理和设计问题，讨论了湍流管入口角、出口角、喉口直径和水缝的选择范围。
The cooling mechanism of the turbulent flow cooler is studied. The choosing range of the input Angle and output Angle of turbulent tube, the diameter of the throat mouth and water gap are discussed.
研究湍流管式冷却器的冷却机理和设计问题，讨论了湍流管入口角、出口角、喉口直径和水缝的选择范围。
The cooling mechanism of the turbulent flow cooler is studied. The choosing range of the input Angle and output Angle of turbulent tube, the diameter of the throat mouth and water gap are discussed.
应用推荐