双层金属结构低温储罐的安装工艺主要有正装法和倒装法。
The installation technique for low temperature storage tank with double layer metal structure is mainly divided into normal assembly method and inverted assembly method.
结合吉林燃料乙醇工程中斜底储罐和盘梯的安装实践，分别介绍了斜底储罐和盘梯的施工方法。
Combined with the installation practice in Jilin fuel ethanol project, the construction methods of tank with oblique bottom and winder are separately discussed.
介绍了管式密封基本原理和构成，管式密封在石油储罐中的安装方法和使用注意事项。
This paper introduces the basic principle and structure of liquid-filled flexible hose Seal, the installing method and operation regulation in oil tank.
阻火器设备是安装于焦化石油储罐上的重要安全设备。
Flame arrester device is installed in the coking of oil storage tanks on the important safety equipment.
流速控制必须安装在循环系统中储罐的回水之前以控制变频泵。
A flow control to install before back flow of the loop into the tank and to head the frequence control pump.
介绍了导链式倒装法安装大型钢制立式储罐的原理及制作工艺流程。
Principles for chain upside -down mounting of big steel vertical big storage tanks and technological process of manufacturing are introduced.
在ChemtrolTru-Bloc关闭阀安装和测试后，连接到满储的储罐的管道开口将不会开始滴漏。
Open piping attached to a filled tank will not start to drip-leak following installation and test of a Chemtrol Tru-Bloc shut-off valve.
液化石油气加气站的设备安装关系到加气站的安全生产，对于液化气储罐和加气机的安装一定要严格手续，用科学严谨的工作态度进行安装。
The procedure should be followed strictly when installing LPG tanks and fillers because the installation is an important step to safe operation. Scientific and serious approach should be taken.
钢制储罐现场安装时，无论是正装法施工还是倒装法施工，焊接变形的控制是关键点。
When steel system kept a bottle the spot to install, regardless was packing a method construction to still set up wrong a method construction, the control which welds to transform is a key to order.
个绍了液化石油气储罐第一道阀门的安装问题，并对安装的阀门类型进行了分析。
The procedure for fixing the first valve of LPG tanks is presented. Types for valve selection are analyzed.
针对球形储罐在制造、安装和使用过程中可能出现的表面缺陷，磁粉检测是重要的检测方法之一。
Magnetic particle testing steps and elements were described in detail, and testing traces of the magnetic particle characteristics, as well as defects in the post-processing methods were introduced.
呼吸阀安装在固定顶罐的通风装置，起减少油品蒸发损耗，控制储罐压力的作用，它也可与阻火器联合安装使用。
Breathing Valve shall be set on roof of the fixed-roof tanks, which can make the tanks safe and reduce the loss of the stored liquids as evaporation.
注射用水储罐的通气口应安装不脱落纤维的疏水性除菌滤器。
Vents of tanks of water for injection shall be protected by a non-fiber-releasing hydrophobic microbial air filter.
注射用水储罐的通气口应安装不脱落纤维的疏水性除菌滤器。
Vents of tanks of water for injection shall be protected by a non-fiber-releasing hydrophobic microbial air filter.
应用推荐