法兰内孔管件内孔必须倒角焊接。
该倒角完确保在安全转移定位。
The chamfered ends ensure secure positioning during transfer.
这是用来倒角打磨的所有工具。
比初始设计更尖锐的过渡段或倒角。
倒角是每个零件必须进行的最后工序。
Champer is the necessary working procedure of every accessory.
轴承的油槽要滚铣和倒角。
可用直角型工件倒角。
效果图显示一对倒角相邻的塔和有明显的支撑。
Renderings show a pair of adjoining towers with chamfered corners and visible bracing.
表1---除倒角外，所有线性尺寸的公差标准。
Table 1 – Accepted deiation for linear measurement except for chamfer edges.
介绍了一种在圆柱零件径向孔孔口倒角用的工具。
In this paper, it deals with the chamfered tool for radial hole of cylindrical part.
其中着重介绍了倒角模块的设计思路和算法实现。
The emphasis is introduction to the design idea and realization of algorithm of fillet module.
用途：用于电瓷产品（棒形、套管）的切割或倒角。
Usage: it is suitable for procelain products(bar, sleeve) to get cutting and chamfering.
倒角：两个表面相交处，通过切掉尖锐边缘形成的平面。
CHAMFER: the flat surface formed by cutting away the sharp edges of two meeting surfaces.
应提供尽可能大的倒角和半径以帮助材料在锻造过程中流动。
Generous fillets and radius should be provided to aid in material flow during the forging process.
选择前面的边并倒角，然后单击应用并以较低的值再次倒角。
Select those front edges and chamfer them then click apply and chamfer it again but this time with a lower value.
可一次装夹可以完成钻孔、铣削、倒角、刚性攻丝等加工工序。
A clamping can be completed drilling, milling, chamfering, rigid tapping and other processing processes.
从工件的承受压力点来看，表现在不同倒角的差异是不明显的。
From the point of stress of the workpiece, the difference at different guide angles is not so obvious.
如果过渡段被电镀(倒角和内切槽)将会产生应力集中，造成裂纹。
Plating into a transition (radius transition or undercut) will create a stress concentration that can cause crack initiation.
介绍了一种高效测量方法，适用于小孔倒角深度的工序间快速检测。
An effectual measuring method applied to inspect the chamfering depth of a small hole in production line is introduced.
这些技术使略带纹理效果的背面和高度抛光的倒角边缘形成强烈对比。
These techniques create a dramatic distinction between the product's lightly textured back and its highly polished chamfered edge.
如果你要创建平滑的过渡，你可以沿着墙和地面交界的边，然后进行倒角。
To create a smooth transition select edges along connection of the wall and the floor and apply Chamfer.
如噪波调节器和倒角的添加可以使整个模型变得不一样，即使肉眼看不出来。
Small things like noise modifiers and edge chamfers can really make a difference later on, even if you don't quite see it in the viewport.
当平行于螺纹构件轴线方向进行测量时，倒角长度应该在1-2全螺纹扣之间。
The length of chamfer shall be between1 and2 complete threads as measured parallel to the axis of the threaded component.
由于圆锥模具缺陷造成的半成品滚子小端倒角缺陷， 滚子小端有尖锐的突出。
NIB : Green roller defect on the small end radius; caused by taper die failure. A sharp protrusion on the small end of the roller.
木螺栓头被设计在交替的几何图案中——特别是一个镶嵌圆形和一个正方形倒角。
The wooden bolt heads are arranged in alternating geometric patterns-specifically an eight-studded circle and a square with inverted corners.
另外还要检查自动卷簧机的调节部位是否灵敏，零件的倒角部分是否加工到位等等。
In addition to check and adjust parts automatic spring coiling machine is a sensitive, chamfer parts processing in place and so on.
另外还要检查自动卷簧机的调节部位是否灵敏，零件的倒角部分是否加工到位等等。
In addition to check and adjust parts automatic spring coiling machine is a sensitive, chamfer parts processing in place and so on.
应用推荐