本文以多轴钻孔组合机床传动箱为实例，对系列产品装配图自动绘制的方法作了探讨。
This paper discusses the assembly drawing of series products as an example of the gear transmission of the multi-spindle head.
行星齿轮传动装置三维建模、装配及动画处理。
Three-dimensional modeling and mechanism simulation of planetary-gear transmission by means of I-DEAS software.
采用该方法对弧齿锥齿轮进行装配和调试，降低了噪声，减小了震动，保证了传动精度。
Using this method in spiral bevel gears' setting, the noise could be reduced, the vibration be decreased and the precision of transmission be ensured.
通过锥蜗杆传动副的啮合分析，用当量圆柱蜗杆副的分析方法，得出阿基米德锥蜗杆副的装配条件。
This paper makes a meshing analysis about the spiroid gearing. Using the method of equivalent worm gearing, the assembly condition of Archimedes spiroid gears has been obtained.
本实用新型具有传动效率高，接触应力小，承受载荷大，结构简单，制造、装配方便，成本低廉等优点。
The utility model has the advantages of high driving efficiency, simple structure, convenient assembly and manufacturing, low cost, small contact stress, big absorbing load, etc.
分析装配误差对正交面齿轮传动的影响是开展面齿轮传动工程应用的重要基础理论之一。
Theoretical analysis of the impact of assembly errors on orthogonal face gear drive is critical to the application of face gear drive.
由于设计、制造和装配误差的存在，三球销式等速万向节的主要零部件之间会有间隙存在，使得传动轴总成在汽车运行过程中产生噪音和振动。
Because of the error of design, manufacturing and assembly, there will be the clearance between the primary components of the tripod constant velocity joint.
齿轮传动搅拌器装配完整的支持。
定、减径机的传动装置的结构简单，易于加工、装配、运输，大大降低成本。
The transmission device for the sizing mill and the reducing mill has simple structure and is easy to be processed, assembled and transported, which reduces cost greatly.
旋转环组件中旋转环3、辅助密封圈2和传动座1之间采用过盈配合装配在一起。
In the rotating ring components, a rotating ring 3, an auxiliary seal ring 2 and a transmission seat 1 are assembled together by clearance fit.
双活塞推动，齿条齿轮传动，结构紧凑，装配位置对称，动作迅速，通过简单的活塞颠倒可以改变输出轴转向。
Dual-piston driven. toothed bar and gear driven, structure is compact, position of assembly is symmetrical. Motion is swift. turning of output axis can be changed through simple reversal of piston.
液压传动。减压阀、顺序阀、卸荷阀、节流阀和止回阀。装配面。
Hydraulic fluid power - Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves - Mounting surfaces.
可装配手柄和气动或电动传动器。
It can be equipped with a manual handle or with pneumatic or electric actuators.
液压传动。减压阀、顺序阀、卸载阀、节流阀和止回阀。装配面。
Hydraulic fluid power - Pressure-reducing valves, sequence valves, unloading valves, throttle valves and check valves - Mounting surfaces.
这些部件包括离合器，变速器，传动轴和驱动器的最后装配。
These parts include the clutch, the transmission, the drive shaft, and the final drive assembly.
安装底座符合ISO5211标准，传动轴套可拆卸加工，以适合阀杆的装配要求。
The seat installation reaches ISO5211, transmission shaft cover can disassemble to fit the shaft …
安装底座符合ISO5211标准，传动轴套可拆卸加工，以适合阀杆的装配要求。
The seat installation reaches ISO5211, transmission shaft cover can disassemble to fit the shaft …
应用推荐