主服务器配置与只读服务器配置。
用ldap主服务器配置主kdc。
如您所见，通过主服务器配置，可为每个目录单独配置选项。
As you've seen, options can be configured on a per-directory basis through the main server configuration.
下面使用mkkrb5srv命令用LDAP主服务器配置主KDC。
Use the mkkrb5srv command to configure the master KDC with the master LDAP server. On the master KDC machine, run the mkkrb5ksrv, as shown below
正如前面提到的，将用两个ldap主服务器配置主kdc，不使用LDAP副本服务器。
As stated earlier, you will configure the master KDC with two LDAP master servers and with no LDAP replica servers.
由于这个原因，要使用ldap主服务器配置从KDC并使用LDAP副本服务器作为备用机制。
That is the reason that you will configure the slave KDC primarily with the master LDAP servers and with the LDAP replica as a fallback mechanism.
因为主kdc和管理服务器需要主体数据库的可读写拷贝来完成所需的修改，所以需要用ldap主服务器配置主kdc。
Since the master KDC and administration servers need the read-write copy of the principal database to make the required changes, you are going to configure the master KDC with the LDAP masters.
如简介所述，您可以配置故障转移服务器，以在主安全服务器发生故障时接管其工作。
As mentioned in the introduction, you can configure failover servers that can take over in the event of a failure of the primary security server.
在使用LDAP目录时，一种非常常见的配置是使用一个主 LDAP服务器和另外几个 LDAP 副本服务器，这种配置可以实现目录数据的负载平衡和高可用性。
When using the LDAP directory, it is very common to have one master LDAP server and a few other LDAP replica servers, so as to achieve the load-balancing and high availability of the directory data.
保存对主配置的修改以启用启动跟踪，重新启动服务器。
Save the changes to the master configuration to enable the start-up traces and restart the server.
关于如何设置和配置nim主服务器的说明，请参见参考资料。
See the Resources section for instructions on how to set up and configure a NIM master server.
包含已配置服务器的主应用程序配置。
Main application configuration containing the configured servers.
在主-主配置中，没有主要服务器，对任何服务器所做的修改都会传播到其他主服务器。
In the master-master configuration, there is no primary server and the changes made to any of the server get propagated to the other masters.
现在，用两个ldap主服务器和三个LDAP副本服务器配置从KDC。
Now configure the slave KDC with the two LDAP master servers and three LDAP replica servers.
p设置主配置服务器节点。
为了测试这个配置，停止一个ldap主服务器，尝试执行一些Kerberos请求(比如kinit、klist或kadmin)。
To test this configuration, stop one master LDAP server and try performing some Kerberos requests (like kinit, klist, or kadmin).
您可以在多个机器上配置安全服务器，以支持主服务器和故障转移服务器。
You can configure the security server over multiple machines to allow for both primary and failover servers.
不能将叶子节点配置成主节点，因为它不能直接访问其非根服务器之外的所有其他节点。
You cannot configure a leaf node as the master node because it does not have direct access to all the nodes other than its non-root server.
为了配置以LDAP作为后端服务器的IBMnas主kdc，需要LDAP服务器主机名(必须是完全限定的)以及根dn和密码。
In order to configure IBM NAS master KDC with LDAP as a back-end server, you need an LDAP server hostname (which must be fully qualified), along with the root DN and password.
主kdc现在配置了两个ldap主服务器。
The master KDC is now configured with the two LDAP master servers.
网络中的每个NIS服务器和客户端都将配置为使用相同的 /etc/ntp.conf文件来与 NIS主服务器通信，以获取时间信息
Each NIS server and client in the network is then configured using the same /etc/ntp.conf file to communicate with the NIS master for their time information
Google之前并没有把IPv 6添加到他们的主站上，因为在少量情况下，如果没有正确配置DNS服务器的话，它就会导致延迟。
Google have previously not added IPv6 to their main sites since in a small number of cases, it can cause delays if DNS servers are incorrectly configured.
通过使用EncryptionExpert提供的SQL复制技术，您可以将故障转移服务器的配置与主服务器的配置同步。
Using SQL replication technology provided by Encryption Expert, you can synchronize the configuration of failover servers with the configuration of the primary server.
使用命令mkkrb5srv配置带有LDAP主服务器的Kerberos 主服务器。
Use the mkkrb5srv command to configure the Kerberos master server with the LDAP master server.
配置了两个系统后，使用以下命令在NIS主服务器上启动NTP后台程序
With both systems configured, start the NTP daemon on the NIS master using
本文讨论如何通过配置IBMnas主kdc和管理服务器(kadmind)使用LDAP目录插件存储ibm NAS身份验证数据。
This article covers how to configure an IBM NAS master KDC and administration server (kadmind) to use an LDAP directory plug-in to store IBM NAS authentication data.
主服务器可以手动创建快照，也可以通过配置 olrconfig.xml 的部分（请参见清单1）来触发接收到commit和/或optimize事件时的快照创建。
The master server can create snapshots manually or by configuring the section of solrconfig.xml (see Listing 1) to trigger snapshot creation when commit and/or optimize events are received.
请注意，从 KDC现在配置了一个LDAP主服务器和三个使用默认preference值的副本服务器。
Please note that right now the slave KDC is configured to one LDAP master server and three replicas with the default preference values.
可以使用IBMTivoliDirectoryServer提供的复制特性把服务器配置成主-主模式或主-副本模式。
IBM Tivoli Directory server provides the replication features that can be used to configure servers in a master-master mode or in a master-replica mode.
可以使用IBMTivoliDirectoryServer提供的复制特性把服务器配置成主-主模式或主-副本模式。
IBM Tivoli Directory server provides the replication features that can be used to configure servers in a master-master mode or in a master-replica mode.
应用推荐