装机试验表明，该材质锤头使用寿命比高锰钢高，特别是铸态中锰钢锤头寿命可提高60%。
The field tests indicated the service life of this alloy steel hammer is higher than high manganese steel, especially the cast can be raised to 60%.
通过自制的冲击腐蚀磨损试验机，施加不同极化电位对高锰钢在矿浆介质中的冲击腐蚀磨损行为进行了试验研究。
Effect of polarization potential on the corrosion-wear behavior of high manganese steel in ore slurry was investigated by a self-made impact corrosive-wear tester.
针对传统上高锰钢作为履带板材料在实际应用中的不足，研究了一种新型的铸造m - B低合金高强度耐磨钢。
A kind of new M-B low-alloy wear resistance steel with high strength has been studied to overcome the deficiency of traditional high-manganese steel used in making grippad.
针对用国标规定的稀硫酸溶解试样、钼蓝光度法测定高锰钢中的硅存在结果偏低的问题，试验验证了用硝酸溶样能保证测定结果的准确性。
The GB stipulates that high manganese steel should be dissolved by rare sulphuric acid, the silicon in the solution should be determined by the molybdenum blue photometric method.
研究了铬加入高锰奥氏体钢中后，原奥氏体高锰钢组织中出现的一种新相。
The austenite manganese steel when added to with Chromium element appears a new phase.
利用EBSD取向成像技术初步分析了含锰15%的热锻态高锰钢和含锰20%的拉伸样品中的两相组织结构及取向特点。
Two phase structures and textures of a 15%mn steel in hot forging state and a tensile-deformed 20%mn steel were analyzed by orientation mapping based on EBSD technique.
结果表明：铸造复合中锰奥氏体钢的耐磨性是高锰钢的5.41倍。
The results show that the wear resistance of casting composite medium manganese steel is 5.41 times that of Hadfield steel.
结果表明，在中、低冲击磨料磨损条件下，试验钢的耐磨性优于中碳低合金耐磨钢和高锰钢。
Under lower and medium impact energy, the abrasive wear resistant performance of the steel metioned is higher than that of low alloyed medium carbon wear resistant steel and high manganese cast steel.
针对传统的高锰钢作为履带板材料在实际应用中的不足，试验采用了一种新型的铸造低合金高强度耐磨钢替代。
A kind of new low-alloy steel with strength was studied to overcome the deficiency of traditional high-manganese steel used in making creeper truck.
介稳奥氏体锰钢具有高耐磨性的原因是其在磨损过程中磨面诱发产生大量的马氏体提高了其抗磨粒的切削和剥离能力。
The high wear resistance of the metastable austenitic Mn-steels lies in the high work hardening caused by induced martensite transformation.
结果表明，高锰钢的平均腐蚀速率显著高于中碳铬合金钢，腐蚀过程中高锰钢有较严重的碱脆开裂现象。
The results showed that the corrosion weight loss rate of high Mn steel was distinctly greater than that of medium carbon chromium steel.
铌化物是在凝固过程中形成，具有细化奥氏体晶粒的作用，并分析研究了铌细化高锰钢奥氏体晶粒的机制。
The results indicate that niobium compounds form during solidification, leading to the refinement of austenite grains. The mechanism of grain refinement has been investigated extensively.
高锰钢的优良耐磨性能使其有广泛的应用范围，但在热处理过程中却难以保证所要求的显微组织，并容易引起脱碳、晶粒长大、裂纹和变形。
High manganese steel are widely used for its excellent abrasion resistance. However it is difficult to avoid defects of decarburization, grain growth, cracking and deformation during heat treatment.
应用波长扫描X射线荧光光谱法对中低合金钢、电工钢、高锰钢、不锈钢中锰元素进行测定。
Manganese elements in low alloy steel, electrician steel, high manganese steel and stainless steel were measured with sequential wavelength scanning X-ray fluorescence spectrometry.
该材料硬度和韧性均较高，抗磨性能好，成本低，是中、低冲击条件下高锰钢的理想替代材料。
This material has the high impact toughness and hardness, the better capability of wearresistance and the lower cost.
结果表明，在不同硬化条件下高锰钢中的硬化组织不同，其加工硬化的机制也不相同。
The research results show that the microstructure and work hardening mechanism are distinguishing under different work hardening effect;
中锰耐磨铸钢属脆性材料，在非强烈冲击条件下使用，是高锰钢耐磨性的2.45倍，适用于破碎中低硬度的矿石。
Medium-magnesium cast steel is brittle and suitable for crushing low or medium hard ores Its abrasion-resistance is 2.45 as high as that of the high-magnesium steel under non-heavy impact conditions.
中锰耐磨铸钢属脆性材料，在非强烈冲击条件下使用，是高锰钢耐磨性的2.45倍，适用于破碎中低硬度的矿石。
Medium-magnesium cast steel is brittle and suitable for crushing low or medium hard ores Its abrasion-resistance is 2.45 as high as that of the high-magnesium steel under non-heavy impact conditions.
应用推荐