我们所要做的应该是将图片放置在幻灯片的顶层,然后将混合模式设为叠加,再将不透明度设为45%左右。
What we’re going to do instead is set it on top of the colored slide and set our blending mode to Overlay. Then throw your opacity to around 45%.
我们所要做的应该是将图片放置在幻灯片的顶层,然后将混合模式设为叠加,再将不透明度设为45%左右。
What we're going to do instead is set it on top of the colored slide and set our blending mode to Overlay. Then throw your opacity to around 45%.
现在您可以随意进行一些试验,即使您在绘图时强制实施了一种特殊的绘图模式或不透明度,看看有什么变化。
Now you can play around, even if you only force a particular painting mode or opacity when painting, just to see the changes.
这些形状应被填充为白色,其混合模式应为柔光,不透明度为100%。
They should be white set to Soft Light blending mode at 100% Opacity.
不透明度的选框紧靠在混合模式旁,确保其值为70%。
Next to the blending mode there's the Opacity box. Make sure it's says 70%.
将它的混合模式设为正片叠底,不透明度为35%,并应用下列图层样式。
Set it to Multiply with 35% Opacity and apply the following layer styles.
设置混合模式为屏幕和减少不透明度到45%。
改变混合模式为屏幕和减少不透明度到20%。
更改星星图层的混合模式为滤色,并降低不透明度到大约20%。
Change the blend mode of the stars to Screen and drop down the opacity to around 20%.
涵盖一切从键绿色屏幕,调整混合模式,以不透明,掩蔽,以及更多。
Cover everything from keying a green screen, to adjusting blend modes, to opacity, to masking, and more.
在该图层上混合模式更改为柔光,然后不透明度降低至约38%。现在向您高光图层添加下列混合选项。
Change the blend mode to Soft light on this layer, and then lower the opacity to around 38%. Now add the following blending options to your highlight layer.
使用较小的画笔绘制镜头上的一些行。更改图层混合模式为屏幕,不透明度降低到15%。
Usesmaller brush to draw some lines on the lens. Change layer blend mode to Screenand reduce Opacity to 15%.
设置层混合模式为“叠加”,降低不透明度到65%。
Set this layer to "overlay" and reduce the opacity to about 65%.
将该层去色,混合模式设为滤色,不透明度70%。然后用色阶将它调暗一点。
Desaturate it and set the blend mode to Screen and opacity to 70%. Then use the levels to darken it a little bit.
现在新建一层,混合模式为柔光,不透明度50%,使用大的软笔刷沿边缘涂抹。
Now create a new layer, set the blending mode to Soft Light, the opacity to 50% and paint with a large Soft Brush around the edges.
将这一层的混合模式改为“滤色”,不透明度45%。
Now change the layer's Blend Mode to Screen and drop the Opacity to 45%.
之后,改变了混合模式的屏幕和不透明度为50%。
After that change the Blend Mode to Screen and the Opacity to 50%.
再次复制背景层,并将其拖到顶层,图层模式-柔光,不透明度41%。
Duplicate the base layer again, drag it to the top and set it to LAYER MODE >> Soft Light 41%.
为第三个圆应用一个类似的粉色渐变,但将其混合模式改为“色相”,不透明度改为60%。
Fill the third ellipse with a pink gradient similarly to the previous one but here change its blend mode to Color and set its opacity to 60%.
我们将这个图层的模式设置为柔光,50%的不透明度。最后我们得到了一个很好的光照效果。
We set this latest layer to Soft light and 50% Opacity, and finally we have a nice lighting effect.
步骤4。将图层模式设置为“叠加”,并调整一下“图层1”的填充不透明度。
Step 4. Set the blend mode to 'Overlay' and change the fill opacity on 'Layout 1'.
设置为“柔光”模式,不透明度为40%。
之后将混合模式改为叠加,不透明度为63%。
Change the blending mode to Overlay and reduce the opacity to 63%.
一改混合模式为柔光,和这次降至15%的不透明度。
I changed the blend mode to Soft Light, and lowered the opacity to 15% this time.
控制不透明度和混合模式的每一层。
俺打岩石纹理背景上叠加模式在非常低的不透明。
I slap a rock texture onto the background in overlay mode at a very low opacity.
我们将这个图层的模式设置为柔光,50%的不透明度。最后我们得到了一个很好的光照效果。
I then set that layer to Overlay and 50% Opacity, then duplicated it and set the duplicate to Soft Light and 50%.
我们将这个图层的模式设置为柔光,50%的不透明度。最后我们得到了一个很好的光照效果。
I then set that layer to Overlay and 50% Opacity, then duplicated it and set the duplicate to Soft Light and 50%.
应用推荐