第二章分析了刀具前刀面、后刀面和边界磨损等磨损表面的特征。
The second chapter analyzes the characters of rack face, flank face and boundary wearing.
分析高效锯切条件下节块的磨损特点和形成最佳表面状态的条件。
Wear characteristics of segments and conditions resulting in the optimum segment appearances are also analyzed.
在建立接触副统计表面分形模型的基础上，分析了不同加载条件下的接触应力对磨损状态的影响。
The statistical fractal model of contact surfaces is presented, and the influence of contact stresses on damage states under different load condition is analyzed.
运用扫描电镜观察了这几种材料在泥沙磨损条件下的磨损表面形貌，分析了它们的磨损机理。
The wear surface morphologies were surveyed by scanning electron microscope (SEM) and wear mechanism was analyzed under the sand slurry wear condition.
本论文在分析现状的基础上，从切削声信号和工件表面纹理这两个方面对刀具磨损状态监测技术进行了研究。
This paper researches on the tool wear condition monitoring by cutting sound signal and workpiece surface texture based on analysis of the relative situation.
简单分析了引风机轴瓦工作表面磨损的原因和处理方法，实际应用中损坏的巴氏合金轴瓦经过焊接修复后，使用效果良好。
Analyze the cause and treatment of worn working surface of bearing pads for induced draft fan, after welding repair, the broken babbit alloy bearing pads in actual application has good usage effect.
用扫描电子显微镜(sem)和X射线光电子能谱仪(XPS)对钢球磨损表面进行了分析。
The worn surfaces of the steel balls were analyzed by scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS).
使用扫描电子显微镜（SEM）和能谱分析（EDS）等观察分析磨损钢球表面的磨痕形貌、化学元素和纳米粒子形态。
The surface morphology of wear scar, nanoparticles and its element distribution have been tested and analyzed by scanning electron microscope(SEM) and energy dispersive spectrometry(EDS).
通过磨屑形貌分析和对磨损表面的观察与分析所得的关于复合材料的磨损机制的结论是一致的。
The conclusion on the wear mechanism of the composite by the debris topography analysis is coincident to that of the SEM analysis on the worn surface.
用扫描电子显微镜和X射线光电子能谱仪观察分析了磨损表面形貌和元素化学形态。
Worn surface morphology and element chemistry configuration of steel ball were analyzed by means of X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM).
同时采扫描电镜对喷嘴磨损表面进行了分析。
Wear surface of nozzle were analysed with scanning electron microscope.
借助SEM及EPMA等手段对磨损表面及亚表面和粘着磨损的材料转移情况进行了观察和分析，并对磨损机制进行了讨论。
The worn surface and sub-sarface. of both composite and its base alloy were examined by SEM and EPMA with special attention on the materials transfer and the wear mechanism.
通过道路试验研究，分析了汽车正时套筒链的磨损机制及销轴和套筒的磨损表面形貌。
By the experiment research on road running test of timing bushing chains for automotive engine, its wear mechanism and the worn surface of pins and bushings were analyzed.
微观分析指出：履带板表面的磨损是多种类型磨损机理的综合结果。
Microscopy showed that the worn surface of track shoe is a combined result of multiple types of wear mechanism.
利用光学金相和电子探针等分析手段，对铅青铜轴套内表面出现凹坑及碎粒造成的磨损失效进行了分析。
The failure mechanism of lead bronze shaft sleeves with many pits on their internal surface is analyzed by optical metallograph and EPMA.
通过用扫描电镜对磨损表面形貌进行的观察分析，探讨了复合涂料涂层的磨损机理。
By using SEM to examine the worn surface morphology, the wear mechanisms of these coatings were explored.
采用扫描电子显微镜观察分析了复合材料磨损表面形貌。
The worn surfaces of the composites were observed on a scanning electron microscope.
用摩擦学的观点分析了冷拔顶头磨损失效过程，提出了冷拔顶头表面强化措施。
Based on analysis of the process of pipe cold-drawing plug's wear-caused failure with the Dointview of friction science, measures for surface strengthening of the said plug were made.
利用扫描电子显微镜对材料的磨损表面进行了观察和分析。
And the worn surfaces morphologies of the reinforced PTFE composites were examined with scanning electronic microscopy (SEM).
对一个实际清淤中磨损失效的泥浆泵轮叶片表面进行宏观观察，并利用扫描电镜作了微观形貌分析。
The abrasive erosion pattern of the impeller blades of a used slurry pump is investigated by macro observation, and analyzed by SEM method.
用X射线衍射分析方法测定了镀层表面结构并作了冲击磨料磨损试验。
The X-ray diffraction was used to determine the structure of the coating surface. At last, the shock abrasive wear test was performed.
通过对不同基体组织轧制白口铁的金相组织、磨损表面和机械性能的分析，研究了具有不同基体组织轧制白口铁的磨损机理。
The abrasive mechanism of rolled white cast iron with various matrixes are studied by investigating the microstructure, abrasive surface and mechanical properties of specimens.
基于微动损伤表面和截面扫描电子显微分析以及涂层原始表面和微动磨损表面X射线衍射分析，探讨了几种涂层的微动损伤机理。
Moreover, the original surfaces and the fretted surfaces and cross-sections of the coatings were analyzed by means of scanning electron microscopy and X-ray diffraction.
采集机械磨损表面形貌轮廓曲线来分析器械部件的使用状态是检验检测工作的常用方法。
By collecting topography profile of worn surface, it is common method that using status of appliance parts is analyzed.
根据摩擦学原理，采用动态磨损模拟试验和表面微观分析研究的方法和技术，对气门动态磨损特性进行了系统的试验研究。
The wear properties of valve are systemically investigated by using dynamic simulation testing and surface microscopic analysis techniques based on principle of tribology.
通过给定的磨损参数，并结合经验数据，给出可能产生的磨粒和磨损表面形貌图谱，为后面的故障诊断和磨粒分析奠定了基础。
Based on wear parameter and experience data, the imitated wear particle and surface images of components were given. These are very useful for the fault diagnosis and wear particle analysis.
并对实验结果、试件表面磨损状况以及各种因素的影响进行了分析并得出相应结论，为提高轴承的使用寿命提供了实验依据。
The thesis also analyses the surface wear condition of the test sample as well as the influence of different factors, providing a experimental basis to enhance the life of bearings.
并对实验结果、试件表面磨损状况以及各种因素的影响进行了分析并得出相应结论，为提高轴承的使用寿命提供了实验依据。
The thesis also analyses the surface wear condition of the test sample as well as the influence of different factors, providing a experimental basis to enhance the life of bearings.
应用推荐