gdb使用串行线与您要调试的内核通信。
The gdb uses the serial line to communicate to the kernel you are debugging.
一条串行线(空调制解调器电缆)将通过机器的串口连接它们。
A serial line (null-modem cable) connects the machines through their serial ports.
它通过串行线、以太网接口或者同时使用二者来监测特定服务(或多个服务)的健康状况。
It monitors the health of a particular service (or services) through either a serial line or Ethernet interface or both.
两个路由器通过串行线联接起来，并且每个路由器通过以太网连接到ThinkPad。
The two routers communicated with each other via serial connection, and each router connected to the ThinkPad through Ethernet. This is shown in our connection diagram.
终端机也已经可以通过几根简单的串行线或者更复杂的多点系统，在短距离内与大型计算机或微型计算机连接。
Terminals could also be hooked up to mainframe and minicomputers over relatively short distances with simple serial lines or with more complex multidrop systems.
本文提出了一种直接提取眼图轮廓线的新方法来快速估计高速串行链路中的数据相关性抖动。
To estimate data dependent jitter(DDJ)in high speed serial links, a new method is proposed for extracting contour of eye diagram directly.
该方法为基于该运算的串行生产线理论研究提供了便捷的条件，并为极大代数的应用提供更优越的条件。
This method offered a convenient term for studying serial - production-line based on maximum algebra and provided more advantages for the application of maximum algebra theory.
在此基础上，成功地给出了具有容错能力的三线制串行传输协议、省电模式转换方法及时间控制输出的实现方案。
Serial transmission protocal of 3-wire model with tolerable error ability, the method of transition to save electricity state and time control output realization is also described.
通过3线串行接口，可以很容易的利用程序对输出功率和通信频道进行配置。
Output power and frequency channels are easily programmable by use of the 3-wire serial interface.
研究了极大代数意义下矩阵的行列单调性质，给出了带缓冲器的多出口串行生产线系统矩阵的行列单调性。
This paper explores the row-column monotonicity of matrix in the light of maximal algebra and presents the row-column monotonicity of multi-exits serial production line system matrix with buffer.
两线 串行接口，实现输出会被强制平仓，调整和上升和下降，在可编程的摆率与测序的延迟时间。 输入和输出电压，以及输入和输出电流和温度是可读的。
The two-wire serial interface enables outputs to be margined, tuned and ramped up and down at programmable slew rates with sequenced delay times.
为了在保持生产线最大通过率的前提下，达到平均在制品量最少的目的，采用模糊控制技术，对串行饱和生产线进行物料准入控制。
Fuzzy control technique is used to control the admission of material to a saturated serial production line, and the objective is to minimize the WIP with maximal throughput.
一个串行端口接点可被用来控制电源，设定G 1,G2和G3电压，选择X线影像增强器视野，或延迟测量实际极间电压(看第4章)。
A serial port interface can be used to take control of the power supply, to set G1, G2 and G3 voltages, to select the XRII field, or to measure back the real electrode voltages (see chapter4).
以由串行生产线抽象而成的串联水箱系统为例，讨论了一类混杂系统（HS）建模的规律，从中探讨混杂系统建模的一般原则．。
The principle of a class of hybrid system modeling is investigated through an example abstracted from tandem production line, some common modelling principles for HS are given.
X9241采用二线串行i2c总线与单片机传递数据。其软件由主程序、中断子程序组成。
Data between X9241 and SCM is transmitted with I2C Bus, and the software includes main program and interrupt subprogram.
把一类串行生产线的建模纳入一种泛结构模块网络建模框架。
In this paper, modeling of series product lines may be grouped in the frame of a general structure block network.
该器件集成了128抽头数字控制电位器，EEPROM的16kbit，和一个2线串行接口。
This device integrates a 128-tap digitally controlled potentiometer, 16kbit of EEPROM, and a 2-wire serial interface.
本文将介绍I2C串行总线的性能，并以串行E2PROM为例，给出在8031上利用I/O线实现I2C串行总线的方法和软件设计。
The feature for I2C serial bus is introduced, and taking the serial E2PROM example, methodology and software design Of achieve I2C serial bus to utilize I/O of 8031 were given.
在串行存储延迟线中，计算机字通过某指定点的一种时间度量。
A time measurement for a given computer word to pass a given point as in serial storage delay-lines.
连接rs232输出直接向您的PC或笔记本电脑，或通过拨号调制解调器和电话线连接的串行端口。
Connect the RS232 output directly to the serial port on your PC or Laptop, or by dial-up connection through modems and phone lines.
数字串行接口可配置用于三线式操作，并且与微控制器和数字信号处理器兼容。
The digital serial interface can be configured for three wire operation and is compatible with microcontrollers and digital signal processors.
你可以检查，如果你有任何跳线插针0和1。一朵针用于串行通信和插线能防止代码上传在黑板上。
You can check if you have any jumper wires plugged into pin 0 and 1. thoses pins are used for serial communication and plugged wires can can prevent the code from being uploaded on the board.
单片机对步进电机的控制有串行控制和并行控制两种方式。本设计采用的是串行控制方式，此方式下单片机控制系统与步进电机驱动器之间只有两条控制线。
The design adopts serial control mode, in this case there are only two controlling lines between the single chip microcomputer system and the driver of the step motor.
此2线接口是一个广泛使用的主机、使用串行时钟（SCL）和串行数据线（SDA）的多从机协议。
The 2-wire interface is a widely used Master, multi-slave protocol using a serial clock (SCL) and a serial data line (SDA).
此2线接口是一个广泛使用的主机、使用串行时钟（SCL）和串行数据线（SDA）的多从机协议。
The 2-wire interface is a widely used Master, multi-slave protocol using a serial clock (SCL) and a serial data line (SDA).
应用推荐